67e6baf05e
Netgear RBx350 are dual band 4 stream 802.11ax mesh devices from the Orbi series. The RBR350 is a router with a WAN and 3 LAN ports. The RBS350 is a satellite without WAN port, only 2 LAN ports and half the flash. The hardware is otherwise identical. They were sold in kits as RBK352, RBK353, RBK354 or RBK355, with one router and 1-4 satellites. Hardware: * SoC: Qualcomm IPQ6018 * RAM: 512MiB 1x Nanya NT5CC256M16ER-EK * Flash: 512MiB Winbond W29N04GZ or 256MiB Winbond W29N02GZ * WLAN 2.4GHz: QCN5022 2x2:2 b/g/n/ax * WLAN 5GHz: QCN5052 2x2:2 a/n/ac/ax * Ethernet: QCA8075 switch with 1 WAN and 3 LAN ports or 2 LAN ports * Serial Config: 3.3V TTL 115200-8-N-1, internal populated header * Serial Layout: 3.3V (don't connect, marked with dot) RX TX GND * LEDs: green/red power, white/red/green/blue status * Buttons: 1x Reset, 1x WPS MAC addresses: * LAN1: base address on label, stored in boarddata partition at 0x8 * LAN2: base + 1 * LAN3: base + 2 * WAN: base + 3 * 2.4GHz WLAN: base + 1 * 5GHz WLAN: base + 2 Flashing Notes: The stock firmware images are signed. Both the bootloader and the stock web interface check the signature and will fail to boot/flash. The bootloader automatically does NMRP when a gigabit LAN connection is present. The stock and factory images contain a U-Boot script that is executed when flashing using NMRP. This is used to alter and persist the U-Boot env with a boot command that works with unsigned firmware. Install OpenWrt: * Get the nmrpflash utility [0] and OpenWrt factory image * Find network interface to use: nmrpflash -L * Start nmrpflash: nmrpflash -i interface -f openwrt-...-factory.img * Connect the device LAN port closest to the power jack to the same network using gigabit * Plug the device in and wait for the bootloader to flash * Unplug and replug the device once the power LED blinks amber Revert to Stock: The boot command needs to be reverted before flashing the stock firmware, otherwise it will fail to boot and get stuck in recovery mode (red power LED flashing). * Run: fw_setenv bootcmd bootipq * Restart the device * Flash the stock firmware RBx350-Va.b.c.d.img using nmrpflash [0]: https://github.com/jclehner/nmrpflash Signed-off-by: Michael Lotz <mmlr@mlotz.ch> Link: https://github.com/openwrt/openwrt/pull/21656 Signed-off-by: Robert Marko <robimarko@gmail.com>
41 lines
809 B
Text
41 lines
809 B
Text
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
8devices,mango-dvk|\
|
|
8devices,mango-dvk-sfp|\
|
|
cambiumnetworks,xe3-4)
|
|
ubootenv_add_mtd "0:APPSBLENV" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
glinet,gl-ax1800|\
|
|
glinet,gl-axt1800|\
|
|
linksys,mr7350|\
|
|
linksys,mr7500)
|
|
ubootenv_add_mtd "u_env" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
netgear,rbr350|\
|
|
netgear,rbs350|\
|
|
netgear,wax214|\
|
|
netgear,wax610|\
|
|
netgear,wax610y|\
|
|
tplink,eap610-outdoor|\
|
|
tplink,eap623od-hd-v1|\
|
|
tplink,eap620-hd-v3|\
|
|
tplink,eap625-outdoor-hd-v1)
|
|
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
yuncore,fap650)
|
|
ubootenv_add_mtd "0:appsblenv" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config
|
|
|
|
exit 0
|