portugalfuturista/openwrt-pf
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions 2
openwrt-pf/target/linux/ipq806x/image/generic.mk
Lukas Stockner d2a75029a5
ipq806x: add support for Aruba AP-32x 
This is a dual-radio 802.11a/b/g/n/ac access point with
dual Gigabit Ethernet.

There are two closely related models: The AP-324, which has external
antenna connectors, and the AP-325, which has internal antennas.
The board appears to be identical, and the same image works on both.
Additionally, the Siemens Scalance W1750D is an OEM variant using
the same board, so the image also works on that.

Unfortunately the factory APBoot bootloader enforces cryptographic
signatures on the firmware before booting, so a modified version
must be flashed via the serial port. See [^1] for details.

Specifications
==============
* Device:       Aruba AP-325 / AP-324
* SoC:          Qualcomm IPQ8068 2x1.4GHz ARMv7-A
* RAM:          512MiB (2x Winbond W632GU6MB-12)
* SPI flash:    4MiB Macronix MX25U3235F
* NAND flash:   128MiB Winbond W29N01HZBINF
* WiFi:         2x Qualcomm QCA9990 (one 2.4G, one 5G)
* Ethernet:     2x 1000BASE-T (Marvell 88E1514 PHY), both PoE-capable
* Power:        PoE 802.3at or 12V DC jack
* LEDs:         Red/Amber/Green status LED, Amber/Green WiFi LED
* Buttons:      1x, behind hole next to DC jack
* Console:      RJ45 connector, Cisco pinout
* USB:          1x USB 2.0 Type A, 1x internal to BLE, SoC has USB 3.0
                host but board is only wired for 2.0
* BLE:          TI CC2540 SoC, connected to USB and UART, unpopulated
                debug header on PCB
* TPM:          Atmel AT97SC3205T

How to install
==============
The stock bootloader APBoot appears to be vendor fork of U-Boot, which
disables much of the usual functionality and comes with its own booting
and firmware upgrade logic.

Unfortunately, this logic enforces RSA signatures on images,
even for the default boot from NAND.

Therefore, a patched bootloader is needed, which is built as a package.
In addition to the signature check removal, this also changes
the serial baudrate to 115200.

Luckily, the stock firmware does not disable the `sf` command
(it just hides it until you run `diag`), so the patched bootloader
can be fetched via TFTP and then flashed via console.

Flashing patched APBoot
-----------------------
* Build OpenWrt, or download `openwrt-ipq806x-generic-aruba_ap-32x-apboot.mbn`
* Connect serial cable and wired ethernet
* Access stock APBoot console at Baud 9600
* Flash patched bootloader:
```
setenv serverip <your TFTP server IP>
setenv autostart n
netget 44000000 openwrt-ipq806x-generic-aruba_ap-32x-apboot.mbn
sf probe 0
sf erase 220000 100000
sf write 44000000 220000 100000
reset
```

Booting OpenWrt
---------------
* Connect serial cable and wired ethernet
* Access patched APBoot console at Baud 115200
* Run `setenv serverip <your TFTP server IP>`
* Run `tftpboot openwrt-ipq806x-generic-aruba_ap-32x-initramfs.ari`

Installing OpenWrt
------------------
* Connect serial cable and wired ethernet
* Access patched APBoot console at Baud 115200
* Consider backing up stock firmware(s) (UBI volumes `aos0` and/or `aos1`)
  by booting into OpenWrt via initramfs (see above) and dumping them
* Wipe and repartition NAND flash (see below for explanation):
```
nand device 0
nand erase.chip
reset
ubi part ubifs
ubi remove ubifs
ubi create ubifs 1
ubi create rootfs_data
```
* Follow steps above to boot OpenWrt via initramfs
* From OpenWrt, persist installation via sysupgrade

Reverting to stock FW
---------------------

The patched bootloader remains compatible with the original firmware,
so you can just wipe the NAND, let APBoot recreate the partitions,
and flash back the `aos0`/`aos1` backup from above.

Current status
==============

Tested and working
------------------

* Console
* Wired GbE (both ports)
* WiFi (both 2.4G and 5G)
* LEDs
* Restart Button
* USB port
* External watchdog
* TPM
* BLE SoC

Future work
-----------

* GPIOs for:
  * power source (8 indicates DC jack, 59 indicates 802.3at)
  * reset source (64 for warm reset, 65 for watchdog)
  * USB overcurrent (63)
* BLE SoC reflashing
  * CC2540 comes with Aruba-specific FW out of the box
  * Debug header is exposed on PCB (pinout GND-VCC-Clock-Data-Reset),
    but that requires disassembly
  * Stock BLE FW appears to support reflashing via UART, but protocol
    would need to be reverse-engineered
* ramoops/pstore
  * It appears that APBoot clears the RAM on boot, might be something
    we can patch out as well
* Porting a modern U-Boot

Flash layout
============

SPI flash
---------

```
0x000000-0x020000 sbl1
0x020000-0x040000 mibib
0x040000-0x080000 sbl2
0x080000-0x100000 sbl3
0x100000-0x110000 ddrconfig
0x110000-0x120000 ssd
0x120000-0x1a0000 tz
0x1a0000-0x220000 rpm
0x220000-0x320000 appsbl
0x320000-0x330000 appsblenv
0x330000-0x370000 art
0x370000-0x380000 panicdump
0x380000-0x390000 certificate
0x390000-0x3a0000 mfginfo
0x3a0000-0x3b0000 flashcache
0x3b0000-0x400000 aosspare
```

Factory NAND flash
------------------
* 32MiB MTD partition `aos0`, formatted as UBI
  * 32MiB UBI volume `aos0`
    * contains kernel+initrd of the primary firmware,
      initrd contains the entire root FS
* 32MiB MTD partition `aos1`, formatted as UBI
  * 32MiB UBI volume `aos1`
    * contains kernel+initrd of the secondary firmware,
      initrd contains the entire root FS
* 64MiB MTD partition `ubifs`, formatted as UBI
  * 64MiB UBI volume `ubifs`
    * Contains UBIFS, overlay-mounted on top of the initrd,
      shared between firmware slots

APBoot understands UBI, and will read the kernel from the
`aos0` or `aos1` volume (depending on `os_partition`)
with fallback to the other one in case a check fails.

Kernels are expected to have a vendor-specific header, the included
script will add that header with the correct checksum but no signature.

OpenWrt NAND flash
------------------

OpenWrt assumes separate UBI volumes for kernel and rootfs,
as well as a volume that must be named `rootfs_data` for the UBIFS.

Unfortunately, APBoot actively checks the UBI volumes at boot, and will
repartition if it doesn't find the volumes that it expects (listed above).

Luckily, it doesn't check their size, only their existence. Therefore,
we can use the following layout:

* 32MiB MTD partition `aos0`, formatted as UBI
  * 32MiB UBI volume `aos0`
    * contains OpenWrt kernel+initrd
* 32MiB MTD partition `aos1`, formatted as UBI
  * 32MiB UBI volume `aos1`
    * contains OpenWrt root squashfs
* 64MiB MTD partition `ubifs`, formatted as UBI
  * small (single-LEB) UBI volume `ubifs`
    * Dummy volume, only there to satisfy APBoot
  * almost 64MiB UBI volume `rootfs_data`
    * contains UBIFS, overlay-mounted on top of the rootfs

[^1]: https://github.com/lukasstockner/ap325-apboot-openwrt

Signed-off-by: Lukas Stockner <lukas@lukasstockner.de>
Link: https://github.com/openwrt/openwrt/pull/20738
Signed-off-by: Paul Spooren <mail@aparcar.org>
2026-06-16 16:08:08 +02:00

642 lines
17 KiB
Makefile
Raw Blame History

DTS_DIR := $(DTS_DIR)/qcom
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += TPLINK_BOARD_ID
define Device/kernel-size-migration
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := *** Kernel partition size has changed from earlier \
versions. You need to sysupgrade with the OpenWrt factory image and \
use the force flag when image check fails. Settings will be lost. ***
endef
define Device/dsa-migration
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
endef
define Device/dsa-migration-from-2_0
DEVICE_COMPAT_VERSION := 2.1
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
endef
define Build/buffalo-rootfs-cksum
( \
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
) >> $@
endef
define Build/edimax-header
$(eval edimax_model=$(word 1,$(1)))
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x1200000 \
-i $@ -o $@.new
@mv $@.new $@
endef
# tune addpattern for Linksys E8350-V1 fw pattern generation
define Build/linksys-bin
$(STAGING_DIR_HOST)/bin/addpattern -p $(FW_DEVICE_ID) -v $(FW_VERSION) $(if $(SERIAL),-s $(SERIAL)) -i $@ -o $@.new
mv $@.new $@
endef
# Use Linksys fw header generator to upgrade openwrt factory image over the native Linksys WEB interface
define Build/linksys-addfwhdr
-$(STAGING_DIR_HOST)/bin/linksys-addfwhdr -i $@ -o $@.new \
;mv "$@.new" "$@"
endef
define Build/apboot-addfwhdr
$(SCRIPT_DIR)/aruba-header.py \
$@ $@.new \
"$(call toupper,$(LINUX_KARCH)) $(VERSION_DIST) Linux-$(LINUX_VERSION), $(VERSION_NUMBER) $(VERSION_CODE)"\
"$(VERSION_NUMBER)" \
"$(VERSION_DIST)" \
os \
"$(word 1,$(1))"
mv "$@.new" "$@"
endef
define Device/DniImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
UBINIZE_OPTS := -E 5
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | netgear-dni
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
append-metadata
endef
define Device/TpSafeImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
TPLINK_BOARD_ID :=
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
IMAGE/sysupgrade.bin := append-rootfs | \
tplink-safeloader sysupgrade | append-metadata
endef
define Device/ZyxelImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | \
pad-to $$(KERNEL_SIZE)
KERNEL_NAME := zImage
IMAGES += factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | \
pad-to $$$$(BLOCKSIZE) | zyxel-ras-image separate-kernel
IMAGE/sysupgrade.bin/squashfs := append-rootfs | \
pad-to $$$$(BLOCKSIZE) | sysupgrade-tar rootfs=$$$$@ | \
append-metadata
endef
define Device/arris_tr4400-v2
$(call Device/LegacyImage)
$(Device/dsa-migration)
DEVICE_VENDOR := Arris
DEVICE_MODEL := TR4400
DEVICE_VARIANT := v2
SOC := qcom-ipq8065
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ath10k-firmware-qca99x0-ct
KERNEL_IN_UBI := 1
endef
TARGET_DEVICES += arris_tr4400-v2
define Device/aruba_ap-32x
$(call Device/LegacyImage)
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-325
DEVICE_ALT0_VENDOR := Aruba
DEVICE_ALT0_MODEL := AP-324
DEVICE_ALT1_VENDOR := Siemens
DEVICE_ALT1_MODEL := Scalance W1750D
SOC := qcom-ipq8068
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SUFFIX := .ari
KERNEL = kernel-bin | append-dtb | uImage none | apboot-addfwhdr Octomore
KERNEL_LOADADDR = 0x41508000
KERNEL_SIZE := 30720k
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-i2c-gpio kmod-tpm-i2c-atmel
endef
TARGET_DEVICES += aruba_ap-32x
define Device/askey_rt4230w-rev6
$(call Device/LegacyImage)
$(Device/dsa-migration)
DEVICE_VENDOR := Askey
DEVICE_MODEL := RT4230W
DEVICE_VARIANT := REV6
SOC := qcom-ipq8065
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
KERNEL_IN_UBI := 1
endef
TARGET_DEVICES += askey_rt4230w-rev6
define Device/asrock_g10
$(call Device/FitImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
SOC := qcom-ipq8064
DEVICE_VENDOR := ASRock
DEVICE_MODEL := G10
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 5332k
DEVICE_PACKAGES := kmod-i2c-gpio ath10k-firmware-qca99x0-ct
IMAGE/nand-factory.bin := append-ubi | edimax-header RN67
endef
TARGET_DEVICES += asrock_g10
define Device/buffalo_wxr-2533dhp
$(call Device/LegacyImage)
$(Device/dsa-migration)
SOC := qcom-ipq8064
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WXR-2533DHP
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += buffalo_wxr-2533dhp
define Device/compex_wpq864
$(call Device/FitImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPQ864
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := qcom-ipq8064
DEVICE_PACKAGES := kmod-gpio-beeper
endef
TARGET_DEVICES += compex_wpq864
define Device/edgecore_ecw5410
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Edgecore
DEVICE_MODEL := ECW5410
SOC := qcom-ipq8068
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@v2.0-ap160
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += edgecore_ecw5410
define Device/extreme_ap3935
$(call Device/LegacyImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Extreme Networks
DEVICE_MODEL := AP3935
SOC := qcom-ipq8068
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
KERNEL_LOADADDR = 0x41408000
KERNEL_SIZE := 14400k
KERNEL_SUFFIX := -uImage
UBINIZE_OPTS := -E 5
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += extreme_ap3935
define Device/fortinet_fap-421e
$(call Device/FitImage)
DEVICE_VENDOR := Fortinet
DEVICE_MODEL := FAP-421E
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := fap-421e
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += fortinet_fap-421e
define Device/ignitenet_ss-w2-ac2600
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := IgniteNet
DEVICE_MODEL := SunSpot AC Wave2
DEVICE_ALT0_VENDOR := Accton Technology Corporation
DEVICE_ALT0_MODEL := EAP1024A
DEVICE_ALT0_VARIANT := V2
SOC := qcom-ipq8068
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-ignitenet_ss-w2-ac2600
endef
TARGET_DEVICES += ignitenet_ss-w2-ac2600
define Device/linksys_e8350-v1
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := E8350
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
FW_VERSION := v1.0.03.003
FW_DEVICE_ID := 8350
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_IN_UBI := 1
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-ubi | check-size 0x04000000 | linksys-addfwhdr | linksys-bin
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += linksys_e8350-v1
define Device/linksys_ea7500-v1
$(call Device/LegacyImage)
$(Device/kernel-size-migration)
$(Device/dsa-migration-from-2_0)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 4096k
KERNEL = kernel-bin | append-dtb | uImage none | \
append-uImage-fakehdr filesystem
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | pad-to $$$$(PAGESIZE)
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea7500-v1
define Device/linksys_ea8500
$(call Device/LegacyImage)
$(Device/kernel-size-migration)
$(Device/dsa-migration-from-2_0)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8500
SOC := qcom-ipq8064
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 4096k
KERNEL = kernel-bin | append-dtb | uImage none | \
append-uImage-fakehdr filesystem
BOARD_NAME := ea8500
SUPPORTED_DEVICES += ea8500
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += linksys_ea8500
define Device/meraki_mr42
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR42
SOC := qcom-ipq8068
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_LOADADDR = 0x44208000
DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform \
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
-kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \
-uboot-envtools ath10k-firmware-qca9887-ct \
ath10k-firmware-qca99x0-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \
kmod-leds-tlc591xx
endef
TARGET_DEVICES += meraki_mr42
define Device/meraki_mr52
$(call Device/FitImage)
DEVICE_VENDOR := Cisco Meraki
DEVICE_MODEL := MR52
SOC := qcom-ipq8068
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_LOADADDR = 0x44208000
DEVICE_DTS_CONFIG := config@2
DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform \
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
-kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \
-uboot-envtools ath10k-firmware-qca9887-ct \
ath10k-firmware-qca9984-ct kmod-eeprom-at24 kmod-hwmon-ina2xx \
kmod-leds-tlc591xx
endef
TARGET_DEVICES += meraki_mr52
define Device/nec_wg2600hp
$(call Device/LegacyImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG2600HP
SOC := qcom-ipq8064
BLOCKSIZE := 64k
BOARD_NAME := wg2600hp
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
pad-rootfs | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += nec_wg2600hp
define Device/nec_wg2600hp3
$(call Device/LegacyImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NEC Platforms
DEVICE_MODEL := Aterm WG2600HP3
SOC := qcom-ipq8062
BLOCKSIZE := 64k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
pad-rootfs | append-metadata
DEVICE_PACKAGES := -kmod-ata-ahci -kmod-ata-ahci-platform \
-kmod-usb-ohci -kmod-usb2 -kmod-usb-ledtrig-usbport \
-kmod-phy-qcom-ipq806x-usb -kmod-usb3 -kmod-usb-dwc3-qcom \
ath10k-firmware-qca9984-ct
endef
TARGET_DEVICES += nec_wg2600hp3
define Device/netgear_d7800
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 D7800
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := D7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := d7800
SUPPORTED_DEVICES += d7800
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Sysupgrade does not work due to rootfs ubi partition size change. \
Use factory image with the TFTP recovery flash routine.
endef
TARGET_DEVICES += netgear_d7800
define Device/netgear_r7500
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500
SUPPORTED_DEVICES += r7500
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500
define Device/netgear_r7500v2
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4 R7500
DEVICE_VARIANT := v2
SOC := qcom-ipq8064
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7500v2
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500v2
SUPPORTED_DEVICES += r7500v2
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct \
ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r7500v2
define Device/netgear_r7800
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk X4S R7800
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7800
SUPPORTED_DEVICES += r7800
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ramoops
endef
TARGET_DEVICES += netgear_r7800
define Device/netgear_xr450
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk XR450
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := XR450
NETGEAR_HW_ID := 29764958+0+256+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ramoops
endef
TARGET_DEVICES += netgear_xr450
define Device/netgear_xr500
$(call Device/DniImage)
$(Device/dsa-migration)
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := Nighthawk XR500
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
NETGEAR_BOARD_ID := XR500
NETGEAR_HW_ID := 29764958+0+256+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-ramoops
endef
TARGET_DEVICES += netgear_xr500
define Device/nokia_ac400i
$(call Device/FitImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
DEVICE_VENDOR := Nokia
DEVICE_MODEL := AC400i
SOC := qcom-ipq8065
DEVICE_DTS := qcom-ipq8065-ac400i
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ac400i
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-hwmon-lm75
endef
TARGET_DEVICES += nokia_ac400i
define Device/qcom_ipq8064-ap148
$(call Device/FitImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := standard
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES += ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148
define Device/qcom_ipq8064-ap148-legacy
$(call Device/LegacyImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP148
DEVICE_VARIANT := legacy
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap148
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
define Device/qcom_ipq8064-ap161
$(call Device/FitImage)
$(call Device/UbiFit)
$(Device/dsa-migration)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := AP161
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-ap161
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap161
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-ap161
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
$(Device/dsa-migration)
DEVICE_VENDOR := Qualcomm
DEVICE_MODEL := DB149
SOC := qcom-ipq8064
DEVICE_DTS := qcom-ipq8064-db149
KERNEL_INSTALL := 1
BOARD_NAME := db149
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
endef
TARGET_DEVICES += qcom_ipq8064-db149
define Device/tplink_ad7200
$(call Device/TpSafeImage)
$(Device/dsa-migration)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := AD7200
DEVICE_VARIANT := v1/v2
DEVICE_ALT0_VENDOR := TP-Link
DEVICE_ALT0_MODEL := Talon AD7200
DEVICE_ALT0_VARIANT := v1/v2
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
TPLINK_BOARD_ID := AD7200
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ramoops kmod-wil6210
endef
TARGET_DEVICES += tplink_ad7200
define Device/tplink_c2600
$(call Device/TpSafeImage)
$(Device/dsa-migration)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer C2600
DEVICE_VARIANT := v1
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := c2600
SUPPORTED_DEVICES += c2600
TPLINK_BOARD_ID := C2600
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ramoops
endef
TARGET_DEVICES += tplink_c2600
define Device/tplink_vr2600v
$(Device/dsa-migration)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := Archer VR2600v
DEVICE_VARIANT := v1
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
IMAGE_SIZE := 12672k
SOC := qcom-ipq8064
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := vr2600v
SUPPORTED_DEVICES += vr2600v
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | \
append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += tplink_vr2600v
define Device/ubnt_unifi-ac-hd
$(call Device/FitImageLzma)
DEVICE_VENDOR := Ubiquiti
DEVICE_MODEL := UniFi AC HD
SOC := qcom-ipq8064
BLOCKSIZE := 64k
IMAGE_SIZE := 14784k
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += ubnt_unifi-ac-hd
define Device/zyxel_nbg6817
$(Device/dsa-migration)
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := NBG6817
SOC := qcom-ipq8065
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
RAS_BOARD := NBG6817
RAS_ROOTFS_SIZE := 20934k
RAS_VERSION := "V1.99(OWRT.9999)C0"
SUPPORTED_DEVICES += nbg6817
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs \
kmod-fs-ext4 losetup
$(call Device/ZyxelImage)
endef
TARGET_DEVICES += zyxel_nbg6817
Reference in a new issue View git blame Copy permalink