Add support for TSW202 PoE switch. This is an RTL8380 based switch
with two SFP slots, and 8 PoE 802.3af one every RJ-45 port.
The max budget is 240W.
The vendor firmware configures the PSE
with a per-port budget of 30.0W.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 16 MiB SPI NOR W25Q80RV, 8Mb_Serial_Flash, low_power
* RAM: 128 MiB Winbond W631GG8NB 151
* Ethernet: 8x 10/100/1000 Mbps with PoE
2x SFP slots
* Buttons: 1 "Reset" button on front panel
* Power: 48V-54V DC barrel jack
* UART: 1 serial header with terminal on the back side.
With ground, rx, tx, and 3.3V
* PoE: 2 XS2184
* LED: 2 i2c SL74HC164
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP with ethernet or fiber
- Switch functions
TODO:
------
- LEDs are always on
- Power-over-Ethernet are always on
Install via web interface:
-------------------------
The openwrt firmware will not accept and flash the sysupgrade image.
It is recommended to flash with sysupgrade -n -f over ssh.
Dokumantation, Bootlogs, and Fotos can be found on
https://git.f2a.space/patrick/openwrt-24.10-tsw202/-/wikis/home
Signed-off-by: Patrick Grimm <patrick@lunatiki.de>
Link: https://github.com/openwrt/openwrt/pull/21003
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Backport several fixes and enhancements for the rtl8365mb DSA driver
from upstream.
The backport includes the following changes:
- Fix for rtl8_4 tag (from v7.1)
- VLAN and Forwarding offload (from v7.2)
Before this backport, all bridge forwarding was handled by the CPU,
causing a significant performance drop between LAN ports, similar
to standard WAN/LAN routing. Enabling hardware forwarding offload
alleviates CPU overhead and restores line-rate switching performance.
Link: https://patch.msgid.link/20260408-realtek_fixes-v1-0-915ff1404d56@gmail.com
Link: https://patch.msgid.link/20260606-realtek_forward-v13-0-b9e409687cbe@gmail.com
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23738
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.18 RTL8261N support was added to the generic Realtek PHY driver
and was dropped from the downstream driver.
So, fix the missing RTL8261N support by including the Realtek PHY kmod
and the relevant firmware.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Verify and clean up client ID and global DUID config values before use, in
order to prevent DHCP client malfunction and loss of IPv4 and/or IPv6
connectivity.
- Accept common separators in the string (colon, dash, spaces/tabs, lf)
- Ignore invalid values (non-hex or odd-numbered length)
- Log a warning for invalid settings
The fall back mechanism is as follows:
If a (user-configured) network.<ifname>.clientid setting is found invalid,
ignore and fall back to using network.globals.dhcp_default_duid. In case
that's also invalid (e.g. has been tampered with), don't pass a client
ID to updhc/odhcpc. In that case, udhcpc/odhcpc will use their defaults,
which currently is the i/f MAC address resp. the i/f DUID-LL.
Only error handling is introduced, no behavior change for valid settings.
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/23662
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not needed when using nvmem. All others left alone.
Move some swport nvmem definitions to the root gmac to avoid a
randomized MAC address for the GMAC. The former inherits from the latter anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22550
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Userspace handling is deprecated. WAN stuff needs to remain as no DSA
yet.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21119
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
No need for malloc + strcpy.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22370
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Clarifies that the struct needs to be over allocated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22370
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Userspace handling was needed before band mac overrides.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22306
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
78110c3 states that the MAC for the WAN interface is LAN + 1.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22306
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
For platform drivers themselves this is not needed. but for gpiochips,
it is to avoid module unload.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23731
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Remove the comment since the macro is descriptive enough.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23731
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Propagate error code from rb4xx_gpio_cpld_set instead of just returning
0.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23731
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Claude seems to get confused by a supposedly NULL of_node. Just use dev.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23731
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add an else branch to do so.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23731
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add a host package, which is a new requirement for nfs-kernel-server.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22889
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
APK compresses it's helptext using LUA and require `zlib`, which isn't
available on the Buildbots. It thens falls back to `gzip`, which embeds the
MTIME, making the binary itself unreproducible.
This commits adds a downstream patch to run `gzip` with `-n`, setting the time
to 0.
Link: https://github.com/openwrt/openwrt/pull/23736
Signed-off-by: Paul Spooren <mail@aparcar.org>
With ccache 4.13, it mandates a minimum of 10.
Fixes: 84cb042e3a ("tools/ccache: update to 4.13.3")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23718
Signed-off-by: Robert Marko <robimarko@gmail.com>
Original ar71xx has this setup:
define WNDAP360_WMAC0_MAC_OFFSET 0x120c
define WNDAP360_WMAC1_MAC_OFFSET 0x520c
/* Reusing wifi MAC with offset of 1 as eth0 MAC */
ath79_init_mac(ath79_eth0_data.mac_addr,
art + WNDAP360_WMAC0_MAC_OFFSET, 1);
ap94_pci_init(art + WNDAP360_CALDATA0_OFFSET,
art + WNDAP360_WMAC0_MAC_OFFSET,
art + WNDAP360_CALDATA1_OFFSET,
art + WNDAP360_WMAC1_MAC_OFFSET);
The ath79 port made a questionable change for eth0 being just art with
no offset. That MAC ends up being the OUI for Atheros.
WNDAP360_WMAC1_MAC_OFFSET is the same as WNDAP360_WMAC0_MAC_OFFSET
except with the first hex value being subtracted by 2, which is not a
valid OUI.
And newer Netgear firmware seems to assign differently as well,
art_120C as a base and the others incremented by 0x8.
Switch the assignment to the latest firmware and add label-mac-device to
document that the first Wi-FI MAC address is printed on the device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22895
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
of_device.h was used only for of_match_device. That is no longer
used in most places so we can drop the extra header.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23071
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Even though 3.8 is quite old, it's still used by Ubuntu 20.04 LTS. Bump
the version to get some extra features.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23521
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Convert the last remaining userspace eeprom for ath9k to nvmem. Well,
easily converted at least.
wifi MAC has to be handled in userspace as the kernel nvram driver works
on memory mapped addresses, not mtd ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14666
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
It appears 683-of_net-add-mac-address-to-of-tree.patch relies on the
mac-address nvmem property being present. These nodes don't need it as
they take it from the eeprom but label-mac-device needs it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14666
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Selection of Sparx5 hwmon driver for LAN969x was upstreamed, so use that
instead of the downstream patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, MDIO driver will print the probe defferal as error.
So, instead of spaming the log, backport the upstream fix for it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This commit adds support for the Sirivision SR-ST3408F,
an 8-port 10G switch with 4x RJ45 ports and 4x SFP ports.
SoC: Realtek RTL9303
RAM: 512 MiB DDR3
Flash: SPI-NOR 16 MiB (Winbond)
Ethernet: 4x RJ45 via RTL8261BE PHY (10G/5G/2.5G/1G/100M/10M)
4x SFP+
LEDs: 1x power, 1x system green
2x RJ45 LEDs/port (link/act, 10G)
1x SFP+ LED/port (link/act)
Button: Reset
Console: Cisco-style RJ45, 115200 8n1
Fan: 4040 12V fan (hardwired)
Power: 12V 3A internal PSU
OpenWrt installation
---------------------
1. Attach to serial console using a Cisco cable, 115200 8n1
2. Power on the switch and rapidly press Esc to interrupt U-Boot
3. Initialize the RJ45 ports by running `rtk network on`
4. Serve the initramfs-kernel.bin image on TFTP, IP 192.168.1.111
5. Use any RJ45 port to connect to your TFTP server
6. Run `tftpboot 0x81000000 initramfs-kernel.bin; bootm`
7. Use `mtd dump` or `dd` to backup the original firmware at `mtd5` first
8. Run sysupgrade to flash sysupgrade.bin into the switch and reboot
Restoring original firmware
-----------------------------
Vendor does not provide firmware images, so you should have made a backup.
Use `mtd write` to restore your backed up copy into the `mtd5` partition.
MAC Address
------------
All interfaces are assigned the same MAC address, from the U-Boot env
`ethaddr`. This MAC address is also printed on the device label.
Signed-off-by: Darell Tan <darell.tan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23686
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Create kernel package for the AD7405 ADC driver.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This adds STM32 Octo Memory Manager support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This adds STM32 Camera Serial Interface (CSI) support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This adds STM32 OCTO and QUAD SPI controller support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The COMMON_CLK_STM32MP215 option is for clock support on MP215 platforms,
and PINCTRL_STM32_HDP is for Hardware Debug Port pin control. They can be
safely removed.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The stm32 target now supports 6.18 kernel as testing.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Update stm32mp1 kernel config for 6.18.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Patch 700-net-stmmac-dwmac-stm32-add-support-of-phy-supply-pro.patch
introduces phy-supply support in dwmac-stm32 driver. But the phy_power_on()
function always returns 0 even if it failed to drive the regulator. So fix
phy_power_on() to return an error if something wrong happened.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Drop upstreamed patches and refresh remaining ones.
Manually rebased:
- 700-net-stmmac-dwmac-stm32-add-support-of-phy-supply-pro.patch
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/22989
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
f227ab4f1285 uclient: fix memory leak of url when backend alloc fails
645236607a3d uclient: free proxy_url in uclient_free
53d2d11fb00d uclient-http: fix NULL deref when digest WWW-Authenticate lacks params
0ba1b8718be5 ucode: check calloc return in uc_uclient_new
5cb19466d076 uclient-fetch: reset redirect counter per request
568c447950c1 uclient-fetch: retry short writes and surface errors
4c4a61a69ac3 uclient-fetch: use strtoull to parse Content-Length
440ca260622d uclient-http: validate Content-Length and chunk sizes from the server
8658324bd234 uclient: cast to unsigned char before ctype classifications
bf403fa0f8e5 uclient-fetch: reject CR in --header values
ec47f4176b1e uclient-fetch: always allocate auth_str and free it on exit
391dacd10d31 uclient-http: fail digest auth when the cnonce cannot be randomized
ba1f4311b099 ucode: clamp read length to the size of the static buffer
0ba47f319b09 uclient-fetch: advance to the next URL between requests
9dd0055d527d uclient: initialize *port for unknown address families
f816506651d5 uclient-http: start digest nonce count at 1
9b9b2da40835 uclient-http: fix 2-byte buffer undercount in digest add_field
80fb1e5ee68b ucode: avoid double-free of SSL context on ssl_init error
d44fb561bbcf ucode: don't clear an unrelated registry slot on free
02562403d2a3 uclient-fetch: close the output file before fetching the next URL
4a63561d0012 uclient-http: initialize fd to -1 so a failed connect can't close stdin
428ae8342118 uclient: cancel pending timers in uclient_free()
ffd8db308289 uclient-fetch: guard SSL debug setup against a missing SSL context
9f4db039a263 ucode: release callback argument references
d2af92b0aad9 uclient-http: resolve redirects against the proxy target URL
5dddda023267 uclient-utils: avoid out-of-bounds pointer in get_url_filename
8507588e7ce7 uclient-http: use the proxy target URL for HTTP authentication
322c89c6ca0a uclient-http: retry 401 auth for all body-less request methods
db3bb00ddda7 uclient-http: accept unquoted digest auth parameter values
5ce9983b2a11 uclient-http: follow 303 and 308 redirects
070c868486dc uclient-fetch: finalize request on invalid 206 Content-Range
83659a5a9bc1 uclient-fetch: concatenate multiple URLs into a single -O file
43bed2753998 ucode: don't leak string references in status()/get_headers()
03b17e4fc793 uclient-fetch: attach credentials to the proxy target, not the proxy
74c07b12f7ab uclient-fetch: don't run the progress meter in spider mode
daad21fa2c17 uclient-fetch: handle init_request failure on the 204 resume retry
Link: https://github.com/openwrt/openwrt/pull/23693
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two leaks in mtd_dump():
- The buffer allocated with malloc(erasesize) is never freed before
returning, leaking erasesize bytes on every call.
- The pre-existing malloc-NULL early return path also leaked the just-
opened fd by returning directly instead of going through cleanup.
Initialize buf to NULL, route the malloc-NULL case through the
existing 'out:' label, and add free(buf) on the cleanup path so both
fd and buf are released consistently on every exit.
Signed-off-by: Anna Kiri <bredcorn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23706
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
After malloc(erasesize) in mtd_check(), the result was never checked
for NULL. On allocation failure, the buf pointer remained NULL and
would later be used in image_check() via read(imagefd, buf + buflen,
...), causing a NULL pointer dereference.
Add a NULL check after the allocation and return early. The early
return path also closes the just-opened fd and frees the strdup'd
colon-separated device-list copy to avoid leaks.
Signed-off-by: Anna Kiri <bredcorn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23705
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Two ignored return values in mtd_write_buffer() caused silent failures:
- lseek() return value was ignored. A failed seek (e.g. EBADF, ESPIPE)
followed by write() would silently write at the wrong offset.
- write() return value was ignored, silently discarding write errors.
This could lead to data corruption on the MTD device without any
indication.
Check both return values, report errors to stderr and return -1 on
failure.
Signed-off-by: Anna Kiri <bredcorn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23552
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Improve some descriptions so that they make the purpose of the
particular firmware package clearer to the user (e.g. as viewed in
verbose package listings).
Signed-off-by: Tim Small <tim@seoss.co.uk>
Link: https://github.com/openwrt/openwrt/pull/23688
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Extreme Networks AP3935's LAN1 port (gmac0/RGMII to AR8035 at MDIO
addr 1) fails to acquire a link if no Ethernet cable is connected at
power-on; the port stays dead even after a cable is later inserted, and
only a network restart recovers it.
The AR803x family enables hibernation mode by default, this setting
overrides it.
Signed-off-by: Grische <github@grische.xyz>
Link: https://github.com/openwrt/openwrt/pull/23208
Signed-off-by: Robert Marko <robimarko@gmail.com>
